DMC TSC-34/RU Especificaciones Pagina 133
- Pagina / 179
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
System Software Diagnostics Guide — September 2006 133
PSTN Diagnostics Tool Reference
The commands under this button are as follows:
HoldCall
Place a call on hold. A call that is on hold is disconnected from the external receive and
transmit data streams that are associated with the Telephony Service Channel (TSC) instance.
Once the call is on hold, the client is free to establish a new call, either by making an outbound
call, or by receiving an inbound call.
RetrieveCall
Retrieve a call that is on hold, and bring it to the active state. The completion of the Retrieve
Call operation is indicated via a Call State event that reports the call state transition to
Connected. Note that if there is a call active when the RetrieveCall command is issued, then
that call will be placed on hold, so the command can be used to alternate between two calls.
ReconnectCall
An alternative to the RetrieveCall command, ReconnectCall will retrieve a call that is on hold
and make it the active call. The difference is that if a call is active when the command is issued,
that call will be dropped rather than put on hold.
Figure 14. Call Hold Command Buttons
Call Transfer Commands
Note: The following commands are advanced functions for technical support use only.
The commands under this button are as follows:
BlindTransfer (single-stage blind-transfer)
Place the target call on hold, make a consultation call to the destination address, and then hand
off the target call to the destination without determining the outcome of the consultation call.
The target call's call state will transition first to HoldPendXfer, and then to Idle.
InitTransfer (part of multi-stage transfer)
Place the target call on hold (HoldPendXfer) and initiate a consultation call to the destination
address.
CompleteTransfer (part of multi-stage transfer)
Transfer the call that was the target of the InitTransfer command to the destination address.
CancelTransfer (part of multi-stage transfer)
Cancel a supervised transfer by dropping the consultation call and reconnecting to the call that
was the target of the transfer operation.
- Dialogic 1
- System Software 1
- Contents 10
- Revision History 11
- About This Publication 13
- Related Information 15
- Diagnostics Overview 17
- System Requirements 21
- Using the Diagnostics 23
- Management Console (DMC) 23
- 3.4 Viewing a Log File 24
- Checking DM3 Architecture 27
- 4.4 Unsupported Boards 28
- 4.5 Tracing Firmware 28
- Processor Fault on a Board 29
- Diagnosing First Call Issues 31
- 6.1 Preparation 35
- Debugging Software 41
- Failure or Crash 44
- • Windows systems: 45
- Tracing CAS Signaling Using 47
- Global Call 47
- Sample application code 48
- Tracing Multiple ISDN Trunks 55
- Using Global Call 55
- 9.2 Requirements 56
- CallInfo Reference 63
- 10.3 Options 64
- CAS Trace Reference 65
- DebugAngel Reference 69
- Console (DMC) Reference 71
- Diagnostics Management 71
- 13.2 Guidelines 72
- 13.3 DMC Main Window 72
- 13.3.1 Menu Bar 73
- 13.3.3 Log File Panel 73
- 13.4 DMC Configuration Dialog 74
- DigitDetector Reference 77
- Dlgsnapshot Reference 79
- 15.3 Options 80
- 15.3.3 Command Line Options 81
- DM3Insight Reference 83
- DM3post Reference 85
- 17.3 Options 86
- • 02H is CAS data 90
- • 04H is R2MF tone data 90
- • 08H is SigDet ON data 90
- • 10H is SigDet OFF data 90
- 18.4 Payload Formats 91
- 18.5 Sample Parser 94
- GCEV_TRACEDATA Reference 100
- 18.6 Sample Parser Output 102
- Getver Reference 103
- 19.3 Output 104
- ISDN Trace Reference 105
- Summary Tool Reference 107
- Intel Telecom Subsystem 107
- %INTEL_DIALOGIC_DIR%\bin 108
- – Board Memory Dumps 109
- – File Versions 109
- KernelVer Reference 113
- MercMon Reference 115
- 23.3 Options 119
- PDK Trace Reference 121
- 24.3 Options 122
- 24.4 Sample Scenarios 122
- Phone Reference 125
- 26.1 Description 127
- 26.2 Guidelines 128
- 26.4.2 The Main Window 129
- 26.4.3 The View Bar 130
- Channel State Commands 131
- Inbound Call Control Commands 132
- Call Hold Commands 132
- Call Transfer Commands 133
- SendISDN Command 134
- Misc. Commands 134
- 26.4.5 Keyboard Navigation 135
- 26.6 PSTN Diagnostics Menus 136
- 26.6.3 View menu 137
- 26.6.4 Help menu 137
- -openlog c:/temp/test.pdlog 138
- QScript Reference 139
- Single Session Variable 140
- Runtime Trace Facility (RTF) 141
- Reference 141
- 28.2 Installing RTF 142
- 28.3 RTF Configuration File 142
- 28.3.1 RTFConfig Tag 143
- 28.3.2 Logfile Tag 145
- 28.3.3 Global Tag 147
- 28.3.4 GLabel Tag 148
- 28.3.5 GClient Tag 149
- 28.3.6 GClientLabel Tag 149
- 28.3.7 Module Tag 150
- 28.3.8 MLabel Tag 151
- 28.3.9 MClient Tag 152
- 28.3.10 MClientLabel Tag 152
- 28.5 rtftool Command 156
- RTFConfigLinux.xml 157
- RTFConfigWin.xml 158
- Explanation 159
- 28.7.1 Introduction 160
- 28.7.4 Cautions 161
- RTFManager Reference 163
- 29.2 Guidelines 164
- 29.3 Starting RTFManager 164
- 29.4 Main Window 164
- 29.4.1 File 165
- 29.4.2 Edit 165
- 29.5 General Tab 166
- 29.6 Filtering Tab 168
- 29.7 Log File Filtering 170
- 29.8 Advanced Tab 171
- Status Monitor Reference 173
- Glossary 175
- , 55, 89 177
- , 56, 125 178
© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales